AT&T 2.0.19 Code drop, stage 1

[aaf/authz.git] / authz-test / TestSuite / Instructions_for_MTCs / MTC_Appr_README.txt

diff --git a/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt b/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt
deleted file mode 100644 (file)
index d7ecee4..0000000
--- a/authz-test/TestSuite/Instructions_for_MTCs/MTC_Appr_README.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-#-------------------------------------------------------------------------------\r
-# ============LICENSE_START====================================================\r
-# * org.onap.aaf\r
-# * ===========================================================================\r
-# * Copyright © 2017 AT&T Intellectual Property. All rights reserved.\r
-# * ===========================================================================\r
-# * Licensed under the Apache License, Version 2.0 (the "License");\r
-# * you may not use this file except in compliance with the License.\r
-# * You may obtain a copy of the License at\r
-# * \r
-#  *      http://www.apache.org/licenses/LICENSE-2.0\r
-# * \r
-#  * Unless required by applicable law or agreed to in writing, software\r
-# * distributed under the License is distributed on an "AS IS" BASIS,\r
-# * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.\r
-# * See the License for the specific language governing permissions and\r
-# * limitations under the License.\r
-# * ============LICENSE_END====================================================\r
-# *\r
-# * ECOMP is a trademark and service mark of AT&T Intellectual Property.\r
-# *\r
-#-------------------------------------------------------------------------------\r
-NOTE: You may find slight differences between this readme doc and your actual output in places such as <YOUR_ATTUID>, times, or other such fields that vary for each run.\r
-\r
-Do NOT replace anything inside square brackets such as [user.name] Some commands listed here use this notation, but they are set up to work by just copying & pasting the entire command.\r
-\r
-run command:           sh ./tc MTC_Appr1\r
-you should see:                MTC_Appr1\r
-                                       SUCCESS! [MTC_Appr1.2014-11-03_11-26-26]\r
-\r
-\r
-open a broswer and goto the gui for the machine you're on. For example, this is the home page on test machine zltv1492: \r
-https://zltv1492.vci.att.com:8085/gui/home \r
-\r
-click on My Approvals\r
-\r
-click the submit button at the bottom of the form with no approve or deny buttons selected\r
-\r
-you should see:     No Approvals have been sent. Try again\r
-\r
-click "Try again" link\r
-\r
-you should see:     The Approval Request page\r
-\r
-NOTE: a radio button is a (filled or unfilled) circle under approve or deny\r
-click the select all link for approve\r
-\r
-you should see:     all radio buttons under approve should be selected\r
-\r
-click the select all link for deny\r
-\r
-you should see:     all radio buttons under deny should be selected\r
-\r
-click the reset button at the bottom of the form\r
-\r
-you should see:     NO radio buttons should be selected\r
-\r
-Try to select both approve and deny for a single entry\r
-\r
-you should:         not be able to\r
-\r
-approve or deny entries as you like, then click submit\r
-\r
-after you have submitted all approvals, go back to My Approvals page\r
-\r
-you should see:     No Approvals to process at this time\r
-\r
-in your command line,\r
-run command:           aafcli ns list name com.test.appr.@[user.name].myProject\r
-\r
-NOTE: what you see here will depend on which entries you approved and denied. Included are 2 examples of what you can see:\r
-\r
-1) If you approve everything\r
-\r
-List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]\r
---------------------------------------------------------------------------------\r
-com.test.appr.<YOUR_ATTUID>.myProject\r
-    Administrators\r
-        <YOUR_ATTUID>@csp.att.com                                                      \r
-    Responsible Parties\r
-        <YOUR_ATTUID>@csp.att.com                                                      \r
-\r
-\r
-2) If you deny everything\r
-\r
-List Namespaces by Name[com.test.appr.<YOUR_ATTUID>.myProject]\r
---------------------------------------------------------------------------------\r
-\r
-\r
-run command:           sh ./tc MTC_Appr2 dryrun\r
-you should see:     a lot of output. It's fine if you see errors for this command.\r
-\r
-run command:        aafcli ns list name com.test.appr\r
-you should see:     List Namespaces by Name[com.test.appr]\r
---------------------------------------------------------------------------------\r
-\r
-\r
-run command:        aafcli ns list name com.test.appr.@[user.name]\r
-you should see:     List Namespaces by Name[com.test.appr.<YOUR_ATTUID>]\r
---------------------------------------------------------------------------------\r
-\r