1 ###############################################################################
\r
3 ## Collector Server config
\r
5 ## - Default values are shown as commented settings.
\r
7 ###############################################################################
\r
13 ## - 8080 is http service
\r
14 ## - https is disabled by default (-1)
\r
16 ## - At this time, the server always binds to 0.0.0.0
\r
18 ## The default port when header.authflag is disabled (0)
\r
19 collector.service.port=8080
\r
21 ## The secure port is required if header.authflag is set to 1 (true)
\r
22 ## Authentication is only supported via secure port
\r
23 ## When enabled - require valid keystore defined
\r
24 collector.service.secure.port=8443
\r
26 ## The keystore must be setup per installation when secure port is configured
\r
27 collector.keystore.file.location=etc/keystore
\r
28 collector.keystore.passwordfile=etc/passwordfile
\r
29 collector.keystore.alias=tomcat
\r
32 ###############################################################################
\r
35 ## If there's a problem that prevents the collector from processing alarms,
\r
36 ## it's normally better to apply back pressure to the caller than to try to
\r
37 ## buffer beyond a reasonable size limit. With a limit, the server won't crash
\r
38 ## due to being out of memory, and the caller will get a 5xx reply saying the
\r
39 ## server is in trouble.
\r
40 collector.inputQueue.maxPending=8096
\r
42 ## Schema Validation checkflag
\r
43 ## default no validation checkflag (-1)
\r
44 ## If enabled (1) - schemafile location must be specified
\r
45 collector.schema.checkflag=1
\r
46 collector.schema.file={\"v1\":\"./etc/CommonEventFormat_27.2.json\",\"v2\":\"./etc/CommonEventFormat_27.2.json\",\"v3\":\"./etc/CommonEventFormat_27.2.json\",\"v4\":\"./etc/CommonEventFormat_27.2.json\",\"v5\":\"./etc/CommonEventFormat_28.4.1.json\"}
\r
48 ## List all streamid per domain to be supported. The streamid should match to channel name on dmaapfile
\r
49 collector.dmaap.streamid=fault=ves_fault|syslog=ves_syslog|heartbeat=ves_heartbeat|measurementsForVfScaling=ves_measurement|mobileFlow=ves_mobileflow|other=ves_other|stateChange=ves_statechange|thresholdCrossingAlert=ves_thresholdCrossingAlert|voiceQuality=ves_voicequality|sipSignaling=ves_sipsignaling
\r
50 collector.dmaapfile=./etc/DmaapConfig.json
\r
52 ## authflag control authentication by the collector
\r
53 ## If enabled (1) - then authlist has to be defined
\r
54 ## When authflag is enabled, only secure port will be supported
\r
55 ## To disable enter 0
\r
58 ## Combination of userid,base64 encoded pwd list to be supported
\r
59 ## userid and pwd comma separated; pipe delimitation between each pair
\r
60 header.authlist=sample1,c2FtcGxlMQ==
\r
62 ## Event transformation Flag - when set expects configurable transformation
\r
63 ## defined under ./etc/eventTransform.json
\r
64 ## Enabled by default; to disable set to 0
\r
65 event.transform.flag=1
\r
67 # Describes at what frequency (measured in minutes) should application try to fetch config from CBS
\r
68 collector.dynamic.config.update.frequency=5
\r
70 ###############################################################################
\r
74 #tomcat.maxthreads=(tomcat default, which is usually 200)
\r